Skip to content
Illustrated map of flight categories in southern Québec at 19:00 UTC on a hot July afternoon: every station from Ottawa to Québec City is VFR, with no rain. Montréal / St-Hubert (CYHU) is VFR.

FLIGHT CATEGORIES 15 JUL 1900Z

VFRMVFRIFRLIFR

Illustration

Density altitude formula, rule of thumb and a METAR example

How to compute pressure and density altitude from a METAR: the exact formula, the rule of thumb, the NWS formula with dew point, and a chart.

13 min read

Density altitude tells you how thin the air is, as an altitude. The higher it is, the longer your takeoff run and the slower your climb. This guide computes it from a METAR, step by step: the pressure altitude, the standard temperature, the formula of our density altitude calculator, the rule of thumb and the US National Weather Service (NWS) density altitude formula, with and without the dew point, so you can see how far apart they are. This guide is part of our series on aviation weather products.

The example on this page, and in the calculator, is a real-format report (constructed, not an observation) for a hot July afternoon at Montréal / St-Hubert (CYHU). It uses a field elevation of 90 ft. That is an example value: before you rely on a result, check the published elevation of your field. A METAR does not give it. In Canada, it is in the Canada Flight Supplement (CFS); in the US, in the Chart Supplement.

The calculator’s headline uses the same method as the ClearMETAR app: 118.8 ft for each degree Celsius above standard, added to the exact pressure altitude, then rounded to the nearest 100 ft. The table under it adds the other methods. The sections below explain each step with the same numbers.

What density altitude is

The TC AIM, MET 8.4.3(d), defines density altitude as “the altitude in ISA at which the air density would be equal to the air density at field elevation at the current temperature”. ISA is the International Standard Atmosphere (below). The FAA pamphlet FAA-P-8740-2, Density Altitude, gives the formal definition: “pressure altitude corrected for nonstandard temperature variations.”

In practice, the number tells you how your aircraft will perform. FAA-P-8740-2 takes an airport at 500 ft with a density altitude of 5,000 ft: aircraft there “will perform as if the airport elevation were 5,000 feet.”

The pamphlet names three factors, under the heading “High, Hot, and Humid”:

  • Altitude. The higher the altitude, the less dense the air.
  • Temperature. The warmer the air, the less dense it is.
  • Humidity. Its effect is on engine power rather than on aerodynamic efficiency (see the humidity section below).

So you compute density altitude in three steps: the pressure altitude, the standard temperature at that pressure altitude, then a correction for the real temperature. The dew point is an optional fourth step.

Pressure altitude from the altimeter setting

Pressure altitude “is the indicated altitude when an altimeter is set to 29.92 in Hg (1013 hPa in other parts of the world)” (FAA-P-8740-2). On the ground, you get it from the field elevation and the altimeter setting in the METAR.

The calculator uses the full formula: the NWS pressure altitude formula, applied to the altimeter setting:

pressure altitude = field elevation + 145,366.45 × (1 − (altimeter setting in hPa ÷ 1013.25)^0.190284)

This works because the altimeter setting is built on the standard atmosphere. A Canadian automated station computes it from its station pressure, with the ICAO Standard Atmosphere and the aerodrome reference elevation in the CFS (MANOBS 12.2.6.1). The calculator converts inches of mercury with 1 inHg = 33.8639 hPa.

Near 29.92, the exact formula moves about 925 ft for each inch of mercury. The rule of thumb rounds this to 1,000 ft: add 1,000 ft for each inch below 29.92, and subtract 1,000 ft for each inch above it. With A2990, 29.92 − 29.90 = 0.02 inHg, so you add 20 ft. In the table below, away from 29.92, the rule gives a correction 6 to 10 % larger than the exact one.

A French METAR gives the QNH in hectopascals, rounded down to the whole hectopascal: Q0995 is 995 hPa (Météo-France, Guide aviation 2024, p. 17). The calculator takes hectopascals as they are. Near sea level, each hectopascal below 1013.25 adds about 27 ft. What QNH, QFE and 29.92 mean, and when you set each one, is in our guide to altimeter settings.

Pressure altitude from the altimeter settingFeet to add to the field elevation
Feet to add to the field elevation to get the pressure altitude, for each altimeter setting: exact (ClearMETAR method) and by the rule of thumb (1,000 ft per inHg).
Altimeter settingExactRule of thumb
A2850965 hPa+1,340 ft+1,420 ft
A2900982 hPa+862 ft+920 ft
A2950999 hPa+392 ft+420 ft
A29921013 hPa+1 ft0 ft
A30001016 hPa−73 ft−80 ft
A30501033 hPa−531 ft−580 ft
A31001050 hPa−983 ft−1,080 ft
Q098028.94 inHg+920 ftNo rule of thumb for hPa here
Q100029.53 inHg+364 ftNo rule of thumb for hPa here
Q101329.91 inHg+7 ftNo rule of thumb for hPa here
Q103030.42 inHg−454 ftNo rule of thumb for hPa here
Rule of thumb: 1,000 ft for each inHg below 29.92. In this table it gives 6 % to 10 % more than the exact value. A negative number means that the pressure altitude is below the field elevation.

ISA temperature at your pressure altitude

The International Standard Atmosphere is the reference for “standard”. Météo-France’s Guide aviation 2024 (glossary, p. 28) gives its values: 15 °C and 1013.25 hPa at sea level, a temperature that falls by 0.65 °C per 100 m in the troposphere, and dry air. That is 1.98 °C per 1,000 ft. FAA-P-8740-2 adds that the performance figures in your Pilot’s Operating Handbook (POH) are generally based on standard sea-level conditions: 15 °C and 29.92 inHg.

ISA temperature = 15 − 1.98 × pressure altitude ÷ 1,000

Use the pressure altitude, not the field elevation. At a pressure altitude of 5,000 ft, ISA is 5.1 °C. The real temperature minus ISA is the deviation: 32 °C at a pressure altitude of 110 ft is about ISA +17.

The last step comes from TC AIM MET 8.4.3(d): “A rough value of density altitude can be approximated by adding 118.8 ft to the aerodrome pressure altitude for every degree Celsius the temperature is above ISA.” Below ISA, you subtract 118.8 ft per degree.

density altitude ≈ pressure altitude + 118.8 × (temperature − ISA temperature)

This is the calculator’s headline.

Rule of thumb or exact formula?

The calculator shows four methods side by side.

Method How it works
Rule of thumb The numbers above, rounded: 1,000 ft per inHg for the pressure altitude, 2 °C per 1,000 ft for ISA, 120 ft per °C above ISA
Headline (118.8 ft per °C) Exact pressure altitude, ISA at 1.98 °C per 1,000 ft, TC AIM’s 118.8 ft per °C, nearest 100 ft
NWS, dry air Station pressure from the altimeter setting, then the NWS density altitude formula with the air temperature
NWS, with the dew point The same formula with the virtual temperature, which adds the effect of water vapour

The NWS formulas come from three sheets: Station Pressure, Density Altitude and the pressure altitude sheet above.

station pressure     = altimeter setting × ((288 − 0.0065 × elevation in m) ÷ 288)^5.2561
vapour pressure e    = 6.11 × 10^(7.5 × Td ÷ (237.3 + Td))            hPa, dew point Td in °C
virtual temperature  = T ÷ (1 − (e ÷ station pressure in hPa) × (1 − 0.622))     T in kelvin
density altitude     = 145,366 × (1 − (17.326 × station pressure in inHg ÷ Tv in rankine)^0.235)

Without a dew point, the calculator uses the air temperature in place of the virtual temperature (dry air).

Here are six cases, computed with the calculator’s code. They are fields at a given elevation, not real airports. All values are in feet.

Field, altimeter, temperature / dew point Rule of thumb Headline (118.8) NWS, dry air NWS, with the dew point
47 ft, A2971, 9 °C / 4 °C −400 −400 −400 −300
90 ft, A2990, 32 °C / 22 °C 2,180 2,200 2,100 2,430
3,940 ft, A3002, 29 °C / 10 °C 6,440 6,400 6,320 6,490
5,885 ft, A3010, 32 °C / 5 °C 9,110 9,100 8,910 9,040
0 ft, A2992, 37.8 °C (100 °F), no dew point 2,730 2,700 2,590 —
0 ft, A2992, 35 °C / 35 °C 2,400 2,400 2,290 3,000

The headline is to the nearest 100 ft, the others to the nearest 10 ft.

What the table shows:

  • On a cold day, the methods agree. At 9 °C, the three dry-air methods are within 12 ft of each other.
  • On warm days, the rules read a little high. In the five warm cases, before rounding, the headline gives 60 to 180 ft more than the NWS dry-air formula, and the rule of thumb 80 to 210 ft more. That errs on the safe side.
  • Humidity goes the other way, and it can be larger. With a 22 °C dew point at 32 °C, the NWS formula adds about 330 ft to the dry value: more than the margin of either rule. Saturated air at 35 °C adds about 710 ft.
  • Charts are estimates too. The rule-of-thumb chart in FAA-P-8740-2 gives 2,500 ft at sea level and 100 °F. For the same air, the NWS dry formula gives 2,590 ft and the headline 2,700 ft.

Humidity

FAA-P-8740-2 says humidity “is not generally considered a major factor in density altitude computations because the effect of humidity is related to engine power rather than aerodynamic efficiency.” It also notes that at 96 °F, the water vapour content of the air can be eight times as great as at 42 °F. Its advice: “If high humidity does exist, however, it is wise to add 10 percent to your computed takeoff distance and anticipate a reduced climb rate.”

The NWS formula puts a number on it with the virtual temperature. In the example of this guide (90 ft, 32 °C, dew point 22 °C), the density altitude goes from 2,100 ft for dry air to 2,430 ft with the dew point.

Three of the numbers you will meet leave humidity out: the headline, the rule of thumb and the Canadian remark. TC AIM Table 8.3 says the remark gives “the dry air density altitude”. On a humid day, read the humidity row of the calculator, and add the FAA’s 10 % to the takeoff distance from your POH.

Worked example from a METAR

VFRCYHUMontréal / St-HubertMETAR
METARCYHU151900Z23012KT15SMFEW05032/22A2990
Few clouds at 5,000 ft. Wind 230° at 12 kt.
32/22Temperature 32°C, dew point 22°C
M means minus. When the two are close, fog and low cloud get likely.
A2990Altimeter 29.90 inHg
Set this on your altimeter to read altitude above sea level.

This is the calculator’s example: a real-format report (constructed, not an observation), with the example elevation of 90 ft. It leaves out the remarks. A real Canadian report gives the sea-level pressure there and, on a day like this, the density altitude after it (TC AIM MET 8.2, below).

  1. Read the report. 32/22 is a temperature of 32 °C and a dew point of 22 °C. A2990 is an altimeter setting of 29.90 inHg.
  2. Pressure altitude. The rule of thumb adds 20 ft: 90 + 20 = 110 ft. The exact formula also gives 110 ft.
  3. ISA temperature. 15 − 1.98 × 0.110 = 14.8 °C. The air is 32 − 14.8 = 17.2 °C warmer than standard.
  4. Density altitude. 110 + 118.8 × 17.2 ≈ 2,150 ft. Without rounding the steps, 2,155 ft. To the nearest 100 ft: 2,200 ft.
  5. Compare. The rule of thumb gives 2,180 ft. The NWS formula gives 2,100 ft for dry air and 2,430 ft with the 22 °C dew point.

On that afternoon, an aircraft at this 90 ft field performs as if the field were at about 2,200 ft, or about 2,400 ft once you count the humidity.

The elevation matters. With 85 ft in place of 90 ft, the same report gives 2,149 ft, which rounds to 2,100 ft. Use the published elevation of your own field.

A field with no weather report

Density altitude belongs to a field, through its elevation. The two fields I fly from, CSE4 and CSB3, have no weather report. For a field like that, you can combine its own elevation with the temperature and altimeter setting of a nearby station. The temperature at your field can be different, so treat the result as an estimate. Our guide to flying from a field without a METAR explains how to choose that station.

The ClearMETAR app does the same. It takes the airport’s own elevation, and the temperature and altimeter setting of the report it shows. For a field with no report, that is the report of the nearest station with a current METAR, and the app names that station and its distance. You judge whether it is close enough.

Canada’s density altitude remark

A Canadian METAR can give the density altitude in its remarks. TC AIM MET 8.2: “Density altitude will be indicated after sea level pressure when the density altitude is 200 ft or more than the aerodrome elevation.” For automated stations (AWOS and LWIS), TC AIM MET 8.4.3(d) says the remark “is only added when the density altitude, rounded to the nearest 100 ft, is 200 ft or higher than the aerodrome elevation”. A density altitude below the aerodrome elevation “is not reported”. TC AIM Table 8.3 says the remarks give “the dry air density altitude”.

MANOBS 12.2.6.3, in the standards for automated stations, gives the token, DENSITY ALT XXXFT, with the same 200 ft rule, and DENSITY ALT MISG when the value is missing. The sample report in TC AIM MET 8.2 writes it in full, DENSITY ALTITUDE 2500FT. The CYHU reports below use the short form:

VFRCYHUMontréal / St-HubertMETAR
METARCYHU231900ZAUTO23020G29KT9SMCLR35/22A2990RMKSLP126DENSITY ALT 2500FT
Sky clear. Visibility 9 SM. Wind 230° at 20 kt, gusting 29.
35/22Temperature 35°C, dew point 22°C
M means minus. When the two are close, fog and low cloud get likely.
A2990Altimeter 29.90 inHg
Set this on your altimeter to read altitude above sea level.
DENSITY ALT 2500FTDensity altitude 2,500 ft
A Canadian remark. The air is as thin as standard air at 2,500 ft, so the aircraft takes off and climbs as it would at that altitude.

This is a real report: CYHU, June 23, 2025, at 19:00Z, from the Iowa Environmental Mesonet (IEM) archive. The station gives 2,500 ft. With the example’s 90 ft elevation, the headline method gives 2,511 ft, which rounds to 2,500 ft. The NWS formula gives about 2,420 ft for dry air and 2,760 ft with the 22 °C dew point.

Two things to know when you read the remark:

  • It is a dry-air value. We compared the 48 hourly CYHU reports of June 23 and 24, 2025, with the four methods, using the example’s 90 ft elevation. In every report, the NWS value with the dew point was 185 to 430 ft higher than the remark. The headline method was within 140 ft of the remark, and the NWS dry-air value within 120 ft. No method matched every report. An automated station reports the temperature to the nearest whole degree (MANOBS 12.2.5.1), and half a degree is about 60 ft of density altitude.
  • It can appear below the 200 ft rule. This automated CYHU report gives DENSITY ALT 100FT:
METARCYHU141700ZAUTOVRB04KT9SMBKN020BKN034OVC06014/10A2989RMKSLP123DENSITY ALT 100FT

It is a real report: CYHU, October 14, 2022, at 17:00Z, from the IEM archive. The 18:00Z and 19:00Z reports also give 100 ft. A density altitude of 100 ft cannot be 200 ft above an aerodrome that is above sea level. The same afternoon also shows the rounding: the 19:00Z and 20:00Z reports both give 15 °C and A2990, but the first says 100 ft and the second 200 ft. So do not read the remark, or its absence, as a test of anything. Compute the value for your own field and your own conditions.

Our guide to METAR remarks decodes the other groups after RMK.

In the United States, the METAR has no density altitude remark: FMH-1, the Federal Meteorological Handbook No. 1 for surface observations, lists none. An ASOS station computes density altitude as auxiliary data (ASOS User’s Guide 5.4). Its voice message adds a remark “when density altitude is > 1,000 feet”, for example “Density altitude two thousand five hundred” (6.5). That guide dates from 1998.

What it does to your aircraft

FAA-P-8740-2 lists what a higher density altitude does:

  • Increased takeoff distance.
  • Reduced rate of climb.
  • Increased true airspeed (but the same indicated airspeed) on approach and landing.
  • Increased landing roll distance.

The POH comes first. In the pamphlet’s words: “A pilot’s first reference for aircraft performance information should be the operational data section of the aircraft owner’s manual or the Pilot’s Operating Handbook developed by the aircraft manufacturer.” Enter your POH charts with the values they ask for. The calculator gives the pressure altitude as well as the density altitude.

Without a POH, the pamphlet points to the Koch chart, which gives “typical representative values” for “personal” airplanes. Its example: at 100 °F and a pressure altitude of 6,000 ft, a 1,000 ft takeoff distance becomes 3,300 ft, and a 500 ft/min climb becomes 120 ft/min. It adds that long grass, sand, mud or deep snow “can easily double your takeoff distance”.

Two more points from FAA-P-8740-2:

  • Leaning. Above a density altitude of 5,000 ft, lean a normally aspirated engine for maximum power on takeoff, unless it has an automatic altitude mixture control. A turbocharged engine need not be leaned for takeoff.
  • Timing. When performance is in question, fly in the cool hours of the day: early morning or late afternoon.

A hot day at a short or grass strip is a good reason to write a density altitude limit into your personal minimums.

Density altitude chart

Density altitude chartClearMETAR method, nearest 100 ft
Density altitude in feet, by pressure altitude (rows) and outside air temperature (columns). ClearMETAR method, the same as the app, rounded to the nearest 100 ft.
Pressure altitude0 °C32 °F5 °C41 °F10 °C50 °F15 °C59 °F20 °C68 °F25 °C77 °F30 °C86 °F35 °C95 °F40 °C104 °F
0 ft−1,800−1,200−60006001,2001,8002,4003,000
1,000 ft−50006001,2001,8002,4003,0003,6004,200
2,000 ft7001,3001,9002,5003,1003,7004,3004,8005,400
3,000 ft1,9002,5003,1003,7004,3004,9005,5006,1006,700
4,000 ft3,2003,8004,3004,9005,5006,1006,7007,3007,900
5,000 ft4,4005,0005,6006,2006,8007,4008,0008,6009,100
6,000 ft5,6006,2006,8007,4008,0008,6009,2009,80010,400
7,000 ft6,9007,5008,1008,6009,2009,80010,40011,00011,600
8,000 ft8,1008,7009,3009,90010,50011,10011,70012,30012,900
Same method as the ClearMETAR app: 118.8 ft for each °C above the ISA temperature (15 °C at sea level, 1.98 °C less per 1,000 ft). Dry air: humidity adds more.

Find the row for your pressure altitude and the column for the temperature. For example, a pressure altitude of 5,000 ft at 30 °C gives a density altitude of 8,000 ft, and sea level at 35 °C gives 2,400 ft. The chart uses the calculator’s headline method, to the nearest 100 ft, for dry air. On a humid day, the real value is higher.

Next: QNH, QFE and 29.92, the settings behind the pressure altitude.

Sources

  1. TC AIM (TP 14371) 2026-2, MET 8.2, 8.4.3(d) and 8.4.4 Table 8.3: the density altitude remark and the 118.8 ft rule, Transport Canada
  2. MANOBS, 8th edition, Amendment 3 (September 2026), 12.2.5.1, 12.2.6.1 and 12.2.6.3, Environment and Climate Change Canada
  3. FAA-P-8740-2, Density Altitude (AFS-8, 2008), Federal Aviation Administration
  4. Density Altitude (formula sheet), NOAA National Weather Service
  5. Station Pressure (formula sheet), NOAA National Weather Service
  6. Pressure Altitude (formula sheet), NOAA National Weather Service
  7. ASOS User's Guide (March 1998), 5.4 and 6.5, NOAA, DOD, FAA and US Navy
  8. Federal Meteorological Handbook No. 1 (FCM-H1-2019): surface weather observations and reports, Office of the Federal Coordinator for Meteorological Services and Supporting Research
  9. Guide aviation 2024, p. 17 (pressure group) and p. 28 (standard atmosphere), Météo-France
  10. ASOS/AWOS/METAR archive (CYHU reports), Iowa Environmental Mesonet

Rules checked on

Common questions

Is density altitude in the METAR?

In Canada, yes, as a remark after the sea-level pressure: TC AIM MET 8.2 and 8.4.3(d) and MANOBS 12.2.6.3 say it appears when the density altitude is 200 ft or more above the aerodrome elevation, but some CYHU AUTO reports give it lower. A US METAR has none (FMH-1 lists no such remark), but an ASOS voice message adds it above 1,000 ft (ASOS User's Guide 6.5).

Does humidity matter?

Yes: FAA-P-8740-2 says to add 10 percent to your computed takeoff distance and expect a reduced climb rate when humidity is high. On a 32 °C day with a 22 °C dew point, the NWS formula gives about 330 ft more than for dry air.

Privacy settings

Choose whether PostHog may measure your visit. Nothing is sent unless this is on.