Skip to content
Illustrated map of flight categories in southern Québec at 14:00 UTC, with light to moderate showers around Montréal and a band of heavier showers west of Ottawa: MVFR from Ottawa to Montréal, IFR at Smiths Falls, VFR to the south and east. Montréal / St-Hubert (CYHU) is MVFR.

FLIGHT CATEGORIES 05 NOV 1400Z

VFRMVFRIFRLIFR

Illustration

Crosswind component: formula, chart and the clock rule

How to work out the crosswind and headwind components: the sine formula, true or magnetic wind, a METAR example, gusts, the clock rule and a chart.

11 min read

This guide shows how to work out the headwind and the crosswind yourself: the formula, true or magnetic wind, a worked METAR example, gusts and variable wind, the clock rule and a component chart. To get the numbers for both ends of your runway in one step, use the crosswind calculator. It does the same math.

The worked example is the wind of the CYHU report in our METAR guide: 20010G18KT at Montréal / St-Hubert, a real-format example, not a real observation. It uses runway 24R and a magnetic variation of 14° W. The sections below explain each number.

In this series: maximum demonstrated crosswind, gusts and tailwind, on what the numbers mean for your takeoff or landing.

The formula

The wind splits into two parts, one across the runway and one along it:

  • The crosswind pushes you sideways: crosswind = wind speed × sin(angle).
  • The headwind blows down the runway, into your nose: headwind = wind speed × cos(angle).

The angle is the difference between the wind direction and the runway heading. Both numbers must use the same reference: both magnetic or both true (next section).

angle     = wind direction − runway heading     (keep it between −180° and +180°)
crosswind = wind speed × sin(angle)             (positive: from the right; negative: from the left)
headwind  = wind speed × cos(angle)             (negative: a tailwind)

If the subtraction gives more than 180°, subtract 360°. If it gives less than −180°, add 360°. Then do the same multiplications with the gust speed to get the gust components.

True or magnetic?

Read true, heard magnetic. A wind that you read in a report is in degrees true. A wind that a controller gives you in Canada or France is in degrees magnetic, like the runway numbers. In northern Canada, the runway headings are true as well (see the exception below).

Wind Reference Source
METAR and SPECI, Canada True TC AIM MET 8.2
TAF, Canada True TC AIM MET 7.3
Upper wind forecast (FB), Canada True TC AIM MET 9.2
Ground control and tower, Canada Magnetic TC AIM RAC 4.2.5 and 4.4.2
AWOS or LWIS voice broadcast, Canada Magnetic in southern domestic airspace, true elsewhere TC AIM MET 1.2.5.2 and 8.4.4
METAR, US True FMH-1 5.5.1
ASOS voice message, US Magnetic ASOS User’s Guide 3.2
Weather messages, France True Météo-France guide, p. 31
Air traffic services, France Magnetic Météo-France guide, p. 31

In Canada, the METAR wind direction is “given in degrees (true) but rounded off to the nearest 10º” (TC AIM MET 8.2). The TAF (MET 7.3) and the upper wind forecast (MET 9.2) are true as well. The wind that ground control and the tower give you is in magnetic degrees (TC AIM RAC 4.2.5 and 4.4.2). Runway numbers are magnetic too: RAC 7.6 takes the example of a runway 04 whose centreline is 044° magnetic.

A Canadian automated voice broadcast (AWOS or LWIS) gives the wind in magnetic degrees in Southern Domestic Airspace and in true degrees elsewhere (TC AIM MET 1.2.5.2 and 8.4.4, Table 8.3). It says which one after the direction: “WIND (direction) (MAGNETIC/TRUE)” (MET 8.5).

In the United States, the METAR wind direction is reported “with reference to true north” (FMH-1 5.5.1). The ASOS computer-generated voice message gives it relative to magnetic north (ASOS User’s Guide 3.2). In France, weather messages give the wind from true north and air traffic services from magnetic north (Météo-France aviation guide, p. 31).

The exception: the Northern Domestic Airspace (NDA). In the NDA, “runway heading is given in degrees true” (TC AIM RAC 2.2.1). There, the METAR wind and the runway heading are both true, so you convert nothing. The same section uses magnetic track for cruising altitudes in the south and true track in the NDA: see VFR cruising altitudes.

How to convert true to magnetic

The magnetic variation is the angle between true north and magnetic north where you are.

  • West variation: add it. Magnetic = true + variation. Near Montréal, 200° true is 214° magnetic.
  • East variation: subtract it. Magnetic = true − variation. Near Vancouver, 200° true is about 185° magnetic.

To go from magnetic to true, do the opposite. The rhyme “east is least, west is best” covers the true-to-magnetic step.

We computed these values with the World Magnetic Model (WMM2025, NOAA) for November 2026, to the nearest degree: 14° W at St-Hubert, 13° W at Plattsburgh (KPBG), 15° E at Vancouver and 2° E at Paris-Charles de Gaulle. The variation changes slowly: at St-Hubert it gets smaller by about 0.1° each year. Take it from a current chart or a current model.

In the crosswind calculator, set the wind reference and the runway reference, then enter the variation. The tool converts the wind before it finds the angle.

What the mistake costs at CYHU

If you skip the conversion, you subtract a true wind from a magnetic runway number. Near Montréal, that puts the angle 14° off. The error can go either way (runway 24R taken as 240° magnetic, 10 kt gusting 18):

Wind (true) Angle Crosswind, steady / gusts
200°, converted to 214° magnetic (correct) 26° 4.4 / 7.9 kt
200°, not converted (wrong) 40° 6.4 / 11.6 kt
260°, converted to 274° magnetic (correct) 34° 5.6 / 10.1 kt
260°, not converted (wrong) 20° 3.4 / 6.2 kt

With a wind from 200°, the mistake makes the crosswind look worse than it is. With a wind from 260°, it hides about 4 kt of gust crosswind.

Step by step with CYHU 20010G18KT

MVFRCYHUMontréal / St-HubertMETAR
METARCYHU051400Z20010G18KT15SM-SHRABKN028OVC06009/04A2971RMKSC6AC2SLP063
Broken clouds at 2,800 ft with light rain showers. Wind 200° at 10 kt, gusting 18.
20010G18KTWind 200° at 10 kt, gusting 18
From 200 degrees true, at 10 knots. Gusts reach 18 knots.

This report is a real-format example, not a real observation. Take runway 24R.

  1. Read the wind. 20010G18KT is from 200° true, at 10 kt, gusting 18 kt.
  2. Put the wind and the runway in the same reference. The runway number is magnetic: 24R is about 240°. The variation at St-Hubert is about 14° W, so add it: 200 + 14 = 214° magnetic.
  3. Find the angle. 214 − 240 = −26°. The wind is 26° off the runway, from the left.
  4. Multiply. sin 26° = 0.438 and cos 26° = 0.899.
    • Crosswind: 10 × 0.438 = 4.4 kt, from the left. In gusts: 18 × 0.438 = 7.9 kt.
    • Headwind: 10 × 0.899 = 9.0 kt. In gusts: 18 × 0.899 = 16.2 kt.

Rounded, runway 24R has a 9 kt headwind (16 kt in gusts) and a 4 kt crosswind from the left (8 kt in gusts). The other end, 06L, has the same numbers with the wind behind you: a tailwind of 9 kt (16 kt in gusts) and a crosswind from the right. These are the numbers in the calculator above.

A runway number is a rounded heading: in the RAC 7.6 example, runway 04 has its centreline at 044° magnetic. If runway 24R were 237° magnetic, the crosswind would be 3.9 kt (7.0 kt in gusts). At 243°, it would be 4.8 kt (8.7 kt in gusts). When one knot matters, enter the published heading in the “Exact runway heading” field and set the runway reference to match it.

Sine table and the clock rule

The share of the wind that becomes crosswind is the sine of the angle. The share that becomes headwind is the cosine.

Angle Crosswind share (sine) Headwind share (cosine)
0° 0.00 1.00
10° 0.17 0.98
20° 0.34 0.94
30° 0.50 0.87
40° 0.64 0.77
45° 0.71 0.71
50° 0.77 0.64
60° 0.87 0.50
70° 0.94 0.34
80° 0.98 0.17
90° 1.00 0.00

Three values are easy to remember. At 30°, the crosswind is half the wind. At 60°, the headwind is half the wind. At 45°, each is 0.71 of the wind. The headwind is not the wind minus the crosswind: at 45° that would give 0.29, not 0.71.

The clock rule estimates the crosswind without a table. Read the angle as minutes on a clock face: 15 minutes is a quarter of the wind, 30 is a half, 45 is three quarters, and 60 or more is all of it. In the example, 26° is about 26 minutes, so 0.43 of 10 kt: 4.3 kt. The exact value is 4.4 kt.

Up to 30°, the clock rule is within 0.01 of the sine. Above 30°, it never gives less than the sine, so its error is on the safe side. It gives 0.024 too much at 40°, 0.043 at 45°, and 0.134 at 60°, the largest error. With 20 kt at 60°, the clock rule says 20 kt; the exact crosswind is 17.3 kt. The clock rule gives no headwind: for that, use the cosine. The chart at the end of this page sets the clock rule against the sine from 10° to 90°.

The gust crosswind number

Do the math twice: once with the mean speed, once with the gust. The gust crosswind is the gust speed × sin(angle). In the example, it is 8 kt against 4 kt steady.

The rule for when a report shows a gust depends on the country:

  • Canada, METAR: when the gusts, averaged over 5 seconds, exceed the mean speed by 5 kt or more in the 10 minutes before the observation, and the peak reaches 15 kt or more (TC AIM MET 8.2).
  • Canada, TAF: when the forecast gust exceeds the mean speed by 10 kt or more (MET 7.3).
  • United States: gusts are rapid changes in speed with 10 kt or more between peaks and lulls in the last 10 minutes (FMH-1 5.4.4).
  • France: when the gusts exceed the mean wind by 10 kt (Météo-France aviation guide, p. 16).

So a wind group without a G can still hide gusts below these thresholds. Which number to compare with your limit, and how much the gust factor adds to your approach speed, is in the guide to crosswind limits and gusts. Your own limit belongs in your personal minimums.

Variable wind: VRB and dddVddd

A report has two ways to say that the wind direction changes.

Group Meaning Canada (TC AIM MET 8.2) United States (FMH-1)
VRB02KT Variable direction, 2 kt Speed under 3 kt. At higher speeds, only when the direction varies by 180° or more, or no single direction can be found. May be used at 6 kt or less (12.6.5 b).
25015G25KT 220V280 Mean 250° true, varying from 220° to 280° The direction varies by 60° or more and by less than 180°, and the mean speed is above 3 kt. The direction varies by 60° or more and the speed is above 6 kt (5.4.2 and 12.6.5 c).

In France, VRB is used for a wind under 3 kt that varies by 60° or more, or when the direction varies by more than 180°. A stronger wind that varies between 60° and 180° gets the two extreme directions (Météo-France aviation guide, p. 16).

VRB. There is no single direction, so there is no angle. The calculator plans for the worst: the full speed as crosswind, from either side, and no headwind. With VRB02KT, that is a 2 kt crosswind on every runway.

A sector such as 220V280. The mean direction is not the worst direction. Take the real-format example 25015G25KT 220V280 on runway 24R, with 14° W:

  • The mean, 250° true (264° magnetic), is 24° off the runway: crosswind 6 kt, 10 kt in gusts.
  • The end of the sector, 280° true (294° magnetic), is 54° off: crosswind 12 kt, 20 kt in gusts.

The calculator checks every whole degree of the sector and adds a “worst in the sector” row for each runway end. Here, the mean alone shows half the worst crosswind. The ClearMETAR app uses the mean direction of a variable sector for its runway wind and does not search the sector, so use the calculator for the worst case.

Which runway end is best

The calculator marks the better end with ★: the most headwind first, then the least crosswind (the larger of the steady and the gust value). For an airport with more than one runway, run it once for each runway and compare all the ends.

The best end for the wind is not always the runway to use. Take a made-up field with a long runway 06/24 and a short runway 10/28, a real-format wind 30015G25KT, and 14° W (314° magnetic):

Runway end Angle Headwind, steady / gusts Crosswind, steady / gusts
28 34° right 12 / 21 kt 8 / 14 kt
24 74° right 4 / 7 kt 14 / 24 kt
10 146° left tailwind 12 / 21 kt 8 / 14 kt
06 106° left tailwind 4 / 7 kt 14 / 24 kt

Runway 28 wins on the wind. If it is too short for your aircraft, runway 24 gives you a 24 kt crosswind in gusts. That is your decision, not the calculator’s.

In Canada, the pilot-in-command shall, “where practicable, land and take off into the wind unless otherwise authorized by the appropriate air traffic control unit” (CARs 602.96(3)(e)). At an uncontrolled aerodrome, TC AIM RAC 4.5.2 says to use the runway most aligned into the wind, or a runway parallel to it, but “the pilot has the final authority” and may use another runway in the interest of safety.

The ClearMETAR app does this for every open runway at the field from the latest METAR. It picks the best end with the same two rules, then the longest runway, and shows that end’s headwind or tailwind and its crosswind, steady and in gusts. With Pro, the crosswind turns amber above your own crosswind limit.

With a calm wind (00000KT), there is no headwind and no crosswind on any runway. I fly from two fields with no weather report, CSE4 and CSB3. For a field like that, the guide weather without a METAR explains how to read the windsock and which runway to use when the wind is calm.

Tailwind

A wind more than 90° off the runway heading gives a negative headwind, which the calculator shows as a tailwind (9 kt, 16 kt in gusts, on 06L in the example); what a tailwind does to your takeoff and landing is in the guide to crosswind limits, gusts and tailwind.

Crosswind component chart

The same math as the calculator: the crosswind and the headwind in whole knots, then the clock rule against the sine. These tables work without JavaScript.

Whole knots. Find the angle between the wind and the runway in the first column, then read across to the wind speed.

Crosswind component, in knots, by angle and wind speed
Angle5 kt10 kt15 kt20 kt25 kt30 kt35 kt
10°1233456
20°235791012
30°35810131518
40°361013161922
45°471114182125
50°481115192327
60°491317222630
70°591419232833
80°5101520253034
90°5101520253035
Headwind component, in knots, by angle and wind speed
Angle5 kt10 kt15 kt20 kt25 kt30 kt35 kt
10°5101520253034
20°591419232833
30°491317222630
40°481115192327
45°471114182125
50°361013161922
60°35810131518
70°235791012
80°1233456
90°0000000
The clock rule against the sine, as a share of the wind speed
AngleClock ruleSine (exact)Clock rule minus sine
10°10 min = 1/6 (0.167)0.174−0.007
15°15 min = 1/4 (0.250)0.259−0.009
20°20 min = 1/3 (0.333)0.342−0.009
30°30 min = 1/2 (0.500)0.5000.000
40°40 min = 2/3 (0.667)0.643+0.024
45°45 min = 3/4 (0.750)0.707+0.043
50°50 min = 5/6 (0.833)0.766+0.067
60°all (1.000)0.866+0.134
70°all (1.000)0.940+0.060
80°all (1.000)0.985+0.015
90°all (1.000)1.0000.000

Clock rule: read the angle as minutes on a clock face. 15 minutes is a quarter of the wind, 30 is a half, 45 is three quarters, and 60 or more is all of it. Up to 30° it is within 0.01 of the sine. Above 30° it never gives less than the sine, so the error is on the safe side.

Sources

  1. TC AIM (TP 14371) 2026-2, MET 1.2.5.2, 7.3, 8.2, 8.4.4 (Table 8.3), 8.5 and 9.2: wind in reports, forecasts and voice broadcasts, Transport Canada
  2. TC AIM (TP 14371) 2026-2, RAC 2.2.1, 4.2.5, 4.4.2, 4.5.2 and 7.6: runway headings, the wind given by ATC, choosing a runway, Transport Canada
  3. CARs 602.96: operations at or in the vicinity of an aerodrome, Justice Laws Website
  4. Federal Meteorological Handbook No. 1 (FCM-H1-2019), 5.4, 5.5 and 12.6.5: wind observing and reporting, Office of the Federal Coordinator for Meteorology
  5. ASOS User's Guide (March 1998), 3.2: wind, NOAA, DOD, FAA and US Navy
  6. Guide aviation 2024, p. 16 (METAR wind group) and p. 31 (glossary: mean wind), Météo-France
  7. World Magnetic Model WMM2025 (coefficients, valid to 2029), NOAA National Centers for Environmental Information

Rules checked on

Common questions

Is crosswind sine or cosine?

Sine: the crosswind is the wind speed times the sine of the angle between the wind and the runway, and the headwind is the speed times the cosine. At 30° the crosswind is half the wind, and at 60° the headwind is half the wind.

Is METAR wind true or magnetic?

True: a METAR gives the wind direction in degrees true in Canada (TC AIM MET 8.2), the US (FMH-1 5.5.1) and France (Météo-France aviation guide, p. 31). The wind that a Canadian controller gives you is magnetic, like the runway numbers (TC AIM RAC 4.2.5 and 4.4.2); in the Northern Domestic Airspace, runway headings are true, so a METAR wind needs no conversion there (RAC 2.2.1).

Privacy settings

Choose whether PostHog may measure your visit. Nothing is sent unless this is on.